An overview of microneedle applications, materials, and fabrication methods

• Zahra Faraji Rad,
• Philip D. Prewett and
• Graham J. Davies

Beilstein J. Nanotechnol. 2021, 12, 1034–1046, doi:10.3762/bjnano.12.77

• chamber where a plasma of reactive ions is formed on the material surface. Etching can be either isotropic, at higher gas pressures, or anisotropic when lower pressures are employed. The most common silicon etchant is sulphur hexafluoride (SF6 + O2) in an inductively coupled plasma etch tool. High aspect

Impact of GaAs(100) surface preparation on EQE of AZO/Al₂O₃/p-GaAs photovoltaic structures

• Piotr Caban,
• Rafał Pietruszka,
• Jarosław Kaszewski,
• Monika Ożga,
• Bartłomiej S. Witkowski,
• Krzysztof Kopalko,
• Piotr Kuźmiuk,
• Katarzyna Gwóźdź,
• Ewa Płaczek-Popko,
• Krystyna Lawniczak-Jablonska and
• Marek Godlewski

Beilstein J. Nanotechnol. 2021, 12, 578–592, doi:10.3762/bjnano.12.48

• luminescence characteristic for zinc substituted by aluminum and accompanied by vacancies. The AZO layers are found to be point defected depending on the surface preparation of the substrate. Also, the INBE/IDLE ratio depends on the GaAs surface etching procedure before the ALD process. Detailed sequence of

Concurrent nanoscale surface etching and SnO₂ loading of carbon fibers for vanadium ion redox enhancement

• Jun Maruyama,
• Shohei Maruyama,
• Tomoko Fukuhara,
• Toru Nagaoka and
• Kei Hanafusa

Beilstein J. Nanotechnol. 2019, 10, 985–992, doi:10.3762/bjnano.10.99

• recently, a technique for nanoscale and uniform surface etching of the carbon fiber surface was developed and a significant enhancement of the negative electrode reaction of vanadium redox flow batteries was attained, although the enhancement was limited to the positive electrode reaction. In this study

• single heat-treatment step. The subsequent thermal oxidation concurrently achieved nanoscale surface etching and loading with SnO2 nanoparticles. The nanoscale-etched and SnO2-loaded surface was characterized by field-emission scanning electron microscopy (FESEM), Raman spectroscopy, and X-ray

• nanoparticles; redox flow batteries; surface etching; Introduction Redox flow batteries (RFBs) are energy conversion and storage devices that involve the reduction and oxidation of electroactive species in electrolyte solutions and have attracted much attention due to their scalability and safety. Various

Preparation and morphology-dependent wettability of porous alumina membranes

• Dmitry L. Shimanovich,
• Alla I. Vorobjova,
• Daria I. Tishkevich,
• Alex V. Trukhanov,
• Maxim V. Zdorovets and
• Artem L. Kozlovskiy

Beilstein J. Nanotechnol. 2018, 9, 1423–1436, doi:10.3762/bjnano.9.135

• surface (Figure 8D and inset of Figure 10G). The dependence on cell diameter is weak in this range. On such a surface, etching of the barrier layer occurs at the bottom of the pore as well as on the borders (joints) between the cells (Figure 10G), and probably at a different rate. It can be seen in the

Effect of the fluorination technique on the surface-fluorination patterning of double-walled carbon nanotubes

• Lyubov G. Bulusheva,
• Yuliya V. Fedoseeva,
• Emmanuel Flahaut,
• Jérémy Rio,
• Christopher P. Ewels,
• Victor O. Koroteev,
• Gregory Van Lier,
• Denis V. Vyalikh and
• Alexander V. Okotrub

Beilstein J. Nanotechnol. 2017, 8, 1688–1698, doi:10.3762/bjnano.8.169

• bonding strength between fluorine and DWCNT surface realizing through different methods. This resulted in fluorine loss together with carbon accompanied by partial surface etching of the DWCNTs fluorinated by F2 and BrF3, while no detectable wall destruction occurred for the plasma-fluorinated DWCNTs. We